Christmas projector not working, eight faults fixed

Most projector faults have a dull cause, such as a tripped outlet, a flat battery or a timer that lost its place. Work through the eight faults below before you send anything back. If a unit is faulty, the warranty section at the end tells you what to expect.

Before you start

Unplug the projector before you wipe a lens or touch a wet adapter. Never look into the aperture of a laser while you test it, and keep it pointed at a wall.

A short indoor test separates a fault in the projector from a fault in the yard. Plug it into a dry indoor outlet and aim it at a plain wall, as the guide to indoor use describes.

If it works inside, the problem sits outdoors, in the outlet, the cord or a setting. If it fails inside as well, the projector itself is at fault.

1. No light at all

Start at the outlet. Outdoor outlets should be GFCI-protected, and a GFCI trips when moisture reaches a plug, so press its reset button and check other outdoor outlets on the same circuit.

Then check every joint between outlet and projector. An outdoor-rated extension cord, a dry adapter and a plug held off the ground fix most dark projectors, and the guide to rain, snow and power covers the setup.

If the outlet is live and the projector stays dark, it may be waiting. A projector in timer mode or with a light sensor can be powered but asleep until dark, so test it in sensor-free mode or after dusk.

2. It switches off after a few hours

This is usually the timer doing its job. The GUSODOR RGB Stars runs 1 to 6 hour cycles per its bullets, with a 6 hour maximum in its spec table, and the GUSODOR snowflake runs 6 hours on and 18 off.

A projector that cuts out early on a warm day or in a tight corner may be overheating. The YUEGANG YG-LA-01 has an overheat cut-off, so give any projector open air and never cover it with a bag or box.

3. It doesn’t come on at dusk

A light sensor that sees a porch light, a streetlight or its own reflection thinks it is still day. Turn the sensor away from the light, or switch to a timer if your model has one.

A cycle timer that skips a night has often lost its place after a power cut. Turn it back on at dusk to restart it, and see timers, remotes and apps for how each type behaves.

4. The remote does nothing

Check the batteries first. The GUSODOR remotes take AAA batteries that are not included, and a weak cell shortens the range well before it stops working.

Then step closer. The listed ranges are best cases, such as 65 ft for the YUEGANG and up to 98 ft in the open for the GUSODOR RGB, and walls cut that to 33 ft or less.

Owners of the Star Shower and the YUEGANG give their remotes mixed reports. If yours stays dead close up with fresh batteries, contact the seller while the projector is under warranty.

5. One color is missing

On an RGB laser each color comes from its own laser diode. If red and green work but blue never appears, that diode has likely failed, and no setting will bring it back.

Rule out the settings first. The GUSODOR RGB Stars has seven color modes, including single colors and pairs, so cycle through them all. Owners report that some colors fail on some units, which makes it a warranty case.

6. The picture is blurry or foggy

An LED projector with a focusing lens needs refocusing whenever you move it. Owners of the Govee H7071 say its figures blur farther from the house, so try it nearer the 10 ft Govee recommends.

A hazy picture on a cold, damp night is usually condensation. Wait a while after switching on, then wipe the outer lens with a soft, dry cloth while the projector is off.

7. It looks too dim

Dim is the most common complaint and the least often a fault. Distance, porch lights and dark walls cause most of it, and six fixes for a dim projector covers each one.

A projector that was bright last week and is faint now is a different matter. Clean the lens and check for fog, and if it keeps fading, treat it as a failing unit.

8. It quit after rain or snow

A projector head rated IP65 or IP67 is built for weather, but the adapter often is not. The YUEGANG adapter and the GUSODOR snowflake plug are IP44, and Govee says the H7073 adapter belongs indoors or in an IP65-rated enclosure.

Some H7073 owners report a failed power adapter, while others say theirs came through snow and ice fine. Dry a wet adapter indoors for a day before testing it, and give it a weatherproof outlet box when it goes back out.

The GUSODOR RGB Stars is sold as “waterproof” and frost-resistant with no IP rating stated. Give it a sheltered spot under an eave in heavy rain if you can.

Warranty and returns

If none of the fixes work, contact the seller while you are still covered. The terms differ a lot across the six, and the comparison table shows them next to the other specs.

Star Shower Ultra 9
Warranty not stated on the listing; the brand’s own maker is the seller and shipper, and the holiday return window is long
Govee H7073
12 months
Govee H7071
1 year
GUSODOR RGB Stars
90 days per the listing
YUEGANG YG-LA-01
1 year
GUSODOR Double-Head Snowflake
90 days per the listing

The YUEGANG YG-LA-01 pairs a $ band price with a 1-year warranty. Owners still report mixed reliability and some units that don’t last the season, as our YUEGANG laser review sets out.

Support and warranty are a large part of what separates the makers, which the brand guide looks at closely. Our shortlist of Christmas projectors that hold up weighs owner reports on reliability.

The top pick section explains why the Star Shower comes first. Its easy returns count for a lot when a unit fails early.

If easy returns matter to you

The Star Shower Ultra 9 is sold and shipped by its maker with a long holiday return window, so a faulty unit is simple to send back. Its Amazon listing states no warranty, laser class or distance, and owners give its sensor and remote mixed reports.

Questions and answers

More questions about projector faults

Why won’t my Christmas projector turn on?

Check the GFCI outlet first, since it trips when moisture reaches a plug. Then check the cord and adapter, and remember that a projector in timer or sensor mode may wait for dark before it lights.

Why does my projector turn off after a few hours?

Most likely its timer. The GUSODOR models run fixed cycles, such as 6 hours on and 18 off. A projector that cuts out early in a warm, tight spot may be hitting its overheat protection.

Why is one laser color not working?

Each color on an RGB laser has its own diode. If one color never shows in any mode, that diode has probably failed, which is a warranty case rather than a setting.

Why doesn’t my projector remote work?

Usually flat or missing batteries, since the GUSODOR remotes ship without AAA cells. Distance and walls also cut the range well below the figure on the listing.

Can a projector adapter get wet?

It should not. Several adapters are only IP44, and Govee says the H7073 adapter belongs indoors or in an IP65-rated enclosure. Keep adapters covered and off the ground.